FirePlace Max Flow is the largest fireplace from the Duy's Oven workshop in Nha Be, made for rooms of 80 to 100 m². It works on the same principle as the Convection model: two fans inside draw room air in through the lower honeycomb grille, send it between the double walls around the combustion chamber, then blow warm air out through the upper grille. At the same time, the fire behind the wide glass door radiates infrared heat out to the front.
Price88.000.000₫ 10% VAT included

In a clip filmed at the workshop, Mr. Duy walks viewers through the fireplace line from smallest to largest. The Compact model, 35.5 cm wide, is made for small rooms. Next comes the Infrared Heating model, whose heating glass is stretched as far as possible across the front to give off the most heat, a good fit for many homes at a moderate cost.
The Max Flow stands at the other end of the row. Its body is 1.2 m wide and 68 cm deep, made for homes with rooms of 80 to 100 m². In a room that size, heat radiating through the glass alone is not enough, so the Max Flow adds a convection fan system to push warm air all around the room. Set inside a home, it looks imposing and seriously cool.
The front has two strips of honeycomb grille, one at the bottom and one at the top. Two fans inside draw the room's own air in through the lower grille. The body has double walls, which take up about 5 cm on each side, so a body 1.2 m wide leaves a combustion chamber 1.1 m wide inside. The air travels through the gap between the two walls, wraps around the combustion chamber, heats up, then blows back into the room through the upper grille.
Above the combustion chamber there is also a separate layer, the one that blows the hot air out. The chimney passes up through this layer to the top. Smoke takes the smoke path, heating air takes the air path, and the two never mix.
The honeycomb grilles are stainless steel. Hot air passes through here all the time, so the workshop chose stainless for durability, then painted it black to blend in with the body.
In just over two minutes at the workshop, Duy covers room sizing, convection airflow through the two honeycomb grilles, the double-wall body, glass door, rear fresh-air intake, and why proper installation matters: the Ø168 stainless steel collar connects to the indoor flue, and running a full 6 m chimney keeps smoke from spilling into the room when you open the door to add wood.
Two 12 V DC fans, 0.59 A each, sit behind the air grilles. The fireplace comes with a circuit board with a Type-C port and a 12 V adapter to power the fans.
The outer wall wraps around the combustion chamber, which makes the fireplace very durable and reduces the chance of small children accidentally touching a hot surface. The gap between the two walls is the path the heating air travels.
The two grille strips at the top and bottom of the front are stainless steel so they can take the hot air passing through, painted black to match the body.
The door is 104 × 47 cm and the opening 100 × 45 cm: sit in front of it and you feel the warmth and can watch the whole fire. The door is very thick and opens forward, so leave clear space in front of the fireplace.
The combustion chamber holds two 304 stainless steel grates, each 53 × 57 cm, and burns both charcoal and wood. Underneath sits a 60 × 62 cm ash tray.
Every fireplace in the FirePlace line has an oxygen intake at the back, and the Max Flow is no exception, with a pipe supplied to fit it. Whether to run that pipe outdoors is up to each household.






Mr. Duy is emphatic about this in the clip: a fireplace is not something you buy, bring home and light straight away like an ordinary grill. It has to be installed properly, because the safety of the whole house depends on it.
That is also why the workshop does not ship a long length of chimney pipe with it. With a pipe on hand, people tend to just plug it in and start using it, which is very dangerous. The workshop only builds the connector on the fireplace; the flue run up to the roof has to be installed by someone who fits it to the actual house.
The chimney collar on top of the Max Flow is Ø168 mm. The bigger the fireplace, the more smoke it has to draw, so its chimney also has to be larger than on the smaller models. At the back is the oxygen intake, with a pipe supplied to fit it; whether it gets used depends on how each house is fitted out.
The fireplace weighs 200 kg and stands on 6 small wheels so it can be rolled into place. When choosing a spot for it, remember to leave clear space in front so the thick glass door can swing open.
| Dimensions (W×D×H) | 120 × 68 × 120 cm |
|---|---|
| Combustion chamber interior | Ngang 110 cm |
| Fireplace opening | 100 × 45 cm |
| Oven doors | Glass door 104 × 47 cm |
| Weight | 200 kg |
| Fuel | Charcoal and wood |
| Heating method | Convection from two fans, plus infrared through the glass door |
| Heating area | Rooms of 80–100 m² |
| Fan | 2 DC fans, 12 V – 0.59 A |
| Power supply | 12 V DC, circuit board with Type-C port, 12 V adapter included |
| Air grilles | Honeycomb, black-painted stainless steel, top and bottom of the front |
| Grates | 2 grates in 304 stainless steel, each 53 × 57 cm |
| Ash tray | 60 × 62 cm |
| Heater Shell | Double walls, heat-resistant paint |
| Chimney Pipe | Ø168 mm collar on top; the flue run up to the roof is fitted by the installer to suit the house |
| Oxygen intake | Rear opening, with 2 air intake pipes of 18 cm |
| Wheel | 6 wheels |
| Warranty | 12 months |
| Price | 88.000.000₫ 10% VAT included |
Handcrafted at the Duy's Oven workshop in Nha Be. Call to ask about pricing and how to route the chimney and oxygen intake pipe for your own home.
Contact us now: 0901 691 717 Chat on ZaloFigures taken straight from the workshop's records, updated whenever the build changes.